Sonic-alert Digital Program Controller DCP301 Manual do Utilizador Página 117
- Página / 187
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 7. PARAMETER SETUP
7-32
No. Item Code Item Factory User Setting
Setting Setting
82 C 8 2 0
83
C 8 3 —
84
C 8 4 0
85 C 8 5 0
86 C 8 6 —
87 C 8 7 —
88 C 8 8 —
89 C 8 q —
90 C q 0 0
91
C q 1
—
92 C q 2 —
93 C q 3 0
94 C q 4 0
95 C q 5 —
96 C q 6 —
97 C q 7 —
98 C q 8 —
99 C q q —
100 C 0 0 —
0: Expansion disabled
1: Expansion enabled
[Note]
This setting is for service use only.
[Note]
“– – – –” is displayed and setting is not possible.
0 to 127
[Note]
On models not supporting communications, “– – – –” is
displayed and setting is not possible.
0 disables communication.
0: 9600bps/even parity, 1 stop bit
1: 9600bps/no parity, 2 stop bits
2: 4800bps/even parity, 1 stop bit
3: 4800bps/no parity, 2 stop bits
[Note]
On models not supporting communications, “– – – –” is
displayed and setting is not possible.
[Note]
“– – – –” is displayed and setting is not possible.
[Note]
Normally set to “0”.
[Note]
“– – – –” is displayed and setting is not possible.
[Note]
“– – – –” is displayed and setting is not possible.
0: Add-on terminal
1 to 15: Loader jack (communications address)
0: Improved
1: Compatible with DCP200
[Note]
“– – – –” is displayed and setting is not possible.
[Note]
This setting is for service use only, and can only be
verified.
Expansion setting 2
Unused
Station address
Transmission rate/
character format
Unused
Unused
Unused
Unused
Special functions
Input 1 zener barrier
adjustment
Unused
CPL communica-
tions port selection
PID type
Unused
Hardware type 1
Hardware type 2
ROM ID
ROM item
ROM revision
- Digital Program Controller 1
- User’s Manual 1
- WARRANTY 2
- TECHNICAL ASSISTANCE 2
- SAFETY PRECAUTIONS 3
- Unpacking 6
- Contents 8
- Chapter 7. PARAMETER SETUP 10
- Chapter 8. PROGRAM SETUP 10
- Chapter 9. TROUBLESHOOTING 11
- Chapter 10 12
- SPECIFICATIONS 12
- Chapter 11. CALIBRATION 12
- RUN/HOLD 13
- 1-1 Features 14
- 1-2 Basic Function Blocks 15
- 1-3 Data Structure 16
- 1-4 System Configuration 17
- 1-5 Model Numbers 18
- 2-1 Structure 19
- 2-2 Console 20
- Basic display state 22
- ■ Loader jack 25
- 2-3 Input Type and Range No 26
- Chapter 3. MOUNTING 28
- 3-2 Panel Cutout Dimensions 29
- 3-3 Mounting 30
- ■ Dust-proof cover 31
- ■ Mounting method 32
- 4-1 Wiring Precautions 33
- 4-2 Compensating Lead 35
- 4-3 Terminal Connections 36
- Direction 37
- ■ Power supply 38
- ■ Ground 38
- Chapter 4. WIRING 39
- ■ Connecting input 1 40
- ■ RS-485 interface 48
- Digital circuit 51
- 5-1 Data 52
- 5-2 Program Patterns 53
- ■ Events 1 to 3 54
- Chapter 5. FUNCTIONS 55
- ■ Time events 1 to 5 57
- ■ G.Soak (guarantee soak) 59
- ■ PID set selection 59
- (1)' 60
- (1)" 60
- ■ Pattern link 61
- 5-3 Modes 62
- ■ Mode transition 64
- ■ Mode transition operations 65
- ■ Mode transition limitations 66
- 5-4 Controller and Programmer 67
- ■ Control output 69
- ● 2G output 71
- ● 3D, 5K outputs 72
- MANUAL mode 72
- ■ SP output 73
- ■ Auxiliary output 73
- 6-1 Turning the Power ON 74
- Chapter 6. OPERATION 75
- Motor valve opening (%) 79
- Output state of events 1 to 3 79
- 6-3 Program Selection 80
- ■ Program selection 82
- ■ Read timing 83
- ■ Manual operation 84
- ■ Auto-tuning (AT) 84
- 7-1 Parameter Setup 86
- 7-2 How to Use 89
- 7-3 Parameter Setup List 92
- Handling Precautions 100
- E T 1 0 103
- E D 1 0 103
- H Y S 1 5 103
- D L 1 0 103
- PID Set No. Designated in the 108
- Program or Zone No. According 108
- ■ Setup data settings “S E t” 112
- SSR' 120
- q 0 (Special functions) 122
- Short-circuit 123
- ■ Table data settings “T B L” 125
- MV upper limit (CH1) 127
- I N S .” blinking 129
- d E L .” blinking 129
- C L R .” blinking 129
- ■ Programming map 131
- ■ Setting up pattern items 132
- ■ Display details 132
- Program No. Segment No 133
- ■ Setting up PV start items 138
- ■ Setting up cycle items 138
- P.L I N 139
- Program No 141
- Copy destination program No 141
- G .R E S 142
- ■ Alarm code display 144
- ■ Alarm categories 144
- 9-4 Replacing the Battery 152
- Comes out towards you 153
- Key cover 153
- Lock screw 153
- Connector 154
- RAM board 154
- (approx. 3cm x 8cm) 154
- Gray holder 155
- 10-1 Specifications 156
- Chapter 10. SPECIFICATIONS 157
- 25 ) and 157
- Item Specification 157
- ■ Accessories/option list 162
- 10-2 External Dimensions 163
- Chapter 11. CALIBRATION 166
- 4.0.4.4 169
- 2.0.2.2 169
- 11-2 Calibration Procedures 170
- ■Function test 171
- 1.0.1.1 174
- Table 11-11 175
- ■Current output calibration 176
- 11-3 Set Up 177
- Programming Map 179
- SAFETY REQUIREMENTS 180
- Revision History 184
- HONEYWELL SERVICE CENTERS 185
- No. CP-UM-5093E 187
Manuais e produtos relacionados com Relógio Sonic-alert Digital Program Controller DCP301
Relógio Sonic-alert SB200ss Manual do Utilizador
(2 páginas)
(2 páginas)
Relógio Sonic-alert SBP100 Manual do Utilizador
(2 páginas)
(2 páginas)
Relógio Sonic-alert SB300SS Manual do Utilizador
(2 páginas)
(2 páginas)
RIKA Cocinas manuales de usuario
Empezando en I
Comentários a estes Manuais